For newer vehicles, particularly German makes, manufacturers are increasingly ditching the transmission dipstick in favor of electronic oil level monitoring. Others may employ a fluid level plug hole on the bottom of the pan.
2013 Ford Fusion transmission oil leveling plug hole. (Courtesy Ford Motor Co.)
In other cases, such as the 2009 Suzuki Equator, the transmission oil dipstick exists but itβs not easy to find! First, it is not a traditional dipstick, sticking out where you can see it. It is a plug with a mounting bolt β youβd never know it is there. Often the ownerβs manual will show the location of the dipstick, if one exists.
Todayβs vehicles have longer maintenance intervals, and the emphasis is on keeping the system sealed to avoid the damage that debris, the wrong oil, and even air and moisture can wreak. In exchange, with electronic oil level monitoring, issues may arise when varnishing reduces the effectiveness of an in-sump sensor, for example.
1. Use the correct fluid β Non-recommended fluids can cause erratic shifts, slippage, abnormal wear, and eventual failure, due to fluid breakdown and sludge formation.
2. Cleanliness β Wipe the dipstick cap and fill tube clean before checking fluid level. Dirt, grease, and other foreign material on the cap and tube could fall into the tube, if not removed beforehand. Use a clean funnel when adding fluid.
3. Incorrect fluid level β A low fluid level allows the pump to take in air along with the fluid. Air in the fluid will cause fluid pressures to be low and develop slower than normal. If the transmission is overfilled, the gears churn the fluid into foam. This aerates the fluid and causes the same conditions occurring with a low level. In either case, air bubbles cause fluid overheating, oxidation, and varnish buildup which interferes with valve and clutch operation. Foaming also causes fluid expansion which can result in fluid overflow from the transmission vent or fill tube. Fluid overflow can easily be mistaken for a leak if inspection is not careful. (via Chrysler)
4. Transmission fluid additives, treatments or cleaning agents β may affect transmission operation and can result in damage to internal transmission components.
5. When to check β Your transmission is not designed to consume fluid. However, check the fluid level if the transmission is not working properly, (eg, if the transmission slips or shifts slowly) or if you notice some sign of fluid leakage.
Planning to service or repair your vehicle? Chilton can help! Access procedures, specifications, tips, and more at ChiltonDIY.com.
Most of us have experienced driving in cold weather and our share of breakdowns. Usually a breakdown is due to the neglect of our vehicle; Iβm just as guilty as the next guy. Weβre busy people! Things we neglect that can cause us to have problems, especially in the winter months:
β’ Battery
β’ Antifreeze
β’ Engine oil
β’ Window washer fluid
β’ Wiper blades
β’ Tires
Here are 6 simple things we can do to help save us from a winter breakdown:
1. Load test the battery. Check and clean the battery connections.
2. Check the condition, strength, and level of the antifreeze. Replace if needed.
3. Check the engine oil condition and level. Replace the engine oil and filter if needed.
4. Refill the window washer bottle and check the spray operation.
5. Inspect and replace the wiper blades as needed.
6. Inspect the tires for tread wear and pressure; rotate if needed.
Β
Refer to Chiltonβs online repair manuals to help keep your vehicle in top shape. Check out ChiltonDIY for repair procedures, maintenance intervals, wiring diagrams, technical service bulletins, Recalls, and more.
Draining and refilling the coolant is one of the easier maintenance tasks you can do on most vehicles. In addition to saving money, doing your own maintenance is a way to monitor the health of your vehicle.
Coolant loses effectiveness over time, so itβs important to periodically drain and refill the cooling system. In addition, as coolant becomes dirty, and rust and particles can eventually degrade cooling system components, such as the engine and water pump.
If you drain the system and then pour coolant in, there is still air trapped within the hoses and components that hold coolant. That air must be removed. Youβll need to bleed out the air and then top off the coolant to the proper level.
Some car manufacturer refill procedures use a special tool that automatically fills the cooling system and bleeds any excess air. In most cases, if you donβt have the special tool, you can still fill the cooling system and bleed it manually. In rare cases, vehicles need to be serviced with specialized cooling system equipment, due to the complexity of the cooling system. Air will become trapped in the cooling system, and cause the engine to overheat! Check the service information before you attempt the procedure.
Caution
Do not work on the coolant system when the system is hot and under pressure: Coolant can cause serious burns. Do not remove the radiator cap, cylinder block drain plugs, or loosen the radiator draincock, when the engine is hot.
1. Tighten the radiator draincock.
2. Tighten the cylinder block drain plug(s).
3. Fill the cooling system with the manufacturer-specified antifreeze. You can find the correct specification in your Chilton DIY subscription or in your ownerβs manual. Because specifications change occasionally, such as with new technology, itβs a good idea to check the technical service bulletins in your ChiltonDIY subscription too.
4. Fill the radiator to the top and install the radiator cap. Add sufficient coolant to the overflow tank to raise the level to the FULL mark. Check your Chilton DIY specifications or the ownerβs manual for the coolant amount including the overflow tank.
Fill the radiator to the top and install the radiator cap. 2010 Chevrolet HHR shown. Image: General Motors.
5. Run the engine with both the radiator cap and reservoir/overflow tank cap in place. Turn on the heat with the blower on high. When the engine reaches normal operating temperature, shut the engine off and allow it to cool.
6. Top off the coolant level to the reserve/overflow tank as necessary to bring it to the FULL mark. Only add coolant when the engine is cold. The coolant level in a warm engine will be higher due to thermal expansion β that is, hot coolant expands and so the coolant level will appear to be higher.
7. Repeat the procedure and recheck the cooling system level.